Last login: Wed Apr 29 21:22:21 on ttys000 gim-yeongdeog-ui-MacBook-Air:~ KimYoungDirk$ ifconfig lo0: flags=8049 mtu 16384 options=3 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 nd6 options=1 gif0: flags=8010

What is the difference between MULTICAST and ALLMULTI ifconfig ifconfig flags. Ask Question Asked 8 years, 8 months ago. Active 8 years, 8 months ago. The ifconfig command outputs its flags in both textual and numeric format. While I can find a reference here or there to the numeric flags, I cannot find any indication on how to interpret (mask) the number. Mar 31, 2019 · What about ifconfig? flags=73 mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10 loop txqueuelen 1000 (Local Loopback) RX packets May 12, 2020 · [root@localhost ~]# ifconfig enp0s3 enp0s3: flags=4163 mtu 1500 inet 192.168.0.103 netmask 255.255.255.0 broadcast 192.168.0.255 ether 08:00:27:1d:8e:54 txqueuelen 1000 (Ethernet) RX packets 33568 bytes 12062979 (11.5 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 20124 bytes 4406857 (4.2 MiB) TX errors Ifconfig Vs IP Command. These commands are just about sufficient in configuring the network in a way any novice or an expert Linux user would want, but due to advancement in Linux kernel over past years and unmaintainable of this packaged set of commands, they are getting deprecated and a more powerful alternative which has ability to replace all of these commands is emerging. The ifconfig utility is used to assign an address and/or configure parameters for a network interface. This utility must be run at boot time to define the network address of each interface present on a machine; it may also be run later on to redefine an interface's address or to configure other interface parameters.

What is the difference between MULTICAST and ALLMULTI ifconfig ifconfig flags. Ask Question Asked 8 years, 8 months ago. Active 8 years, 8 months ago.

Nov 20, 2006 · You can configure an Ethernet card, wireless card, loop back interface or any other network interface device with ifconfig. As an example, if you want to set up the IP address of your Ethernet card, you can pass the necessary options to the ifconfig command as follows: # ifconfig p2p1 192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255 up

eth0: flags=4099 mtu 1500 ether 00:w0:4c:u6:97:11 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 # ifconfig -a ed0: flags=8843 mtu 1500 inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255 ether 01:02:03:04:05:06 lp0 This flags that outbound packets with a particular skb-priority should be tagged with the particular vlan priority vlan-qos. The default vlan priority is 0. set_ingress_map [vlan-device] [skb-priority] [vlan-qos] This flags that inbound packets with the particular vlan priority vlan-qos should be queued with a particular skb-priority. [root@localhost ~]# ifconfig enp0s3: flags=4163 mtu 1500 inet 192.168.100.5 netmask 255.255.255.0 broadcast 192.168.100.255 inet6 fe80::72fa:5672:4f5d:ea72 prefixlen 64 scopeid 0x20 ether 08:27:72:da:42:65 txqueuelen 1000 (Ethernet) RX packets 13534 bytes 18672794 (17.8 MiB) RX errors 0 dropped 0 overruns 0 frame Not able to see wlan0 on executing the command ifconfig: The output on executing the command ifconfig is eth0: flags=4163 mtu 1500 inet 10.0.2.15 n Mar 09, 2020 · i have tried many things and followed your step from other Q&A. I am new to kali linux root@kali:~# ifconfig eth0: flags=4163